Differences

This shows you the differences between two versions of the page.

--- amc2022:grouph:here [2022/08/10 12:13] – created gustavo001
+++ amc2022:grouph:here [2023/01/05 14:38] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
-======  Build ======
+======  Build and Set-Up Deep Sleep ESP 32 ======
-======  Code ======
+{{ :amc2022:grouph:setup_deepsleep.jpeg?nolink&400 |}}
-======  Description ======
+//**figure 4.1**// Deep-Sleep set up for ESP32/
+======  Schematics ======
+{{ :amc2022:grouph:sleep_schematics_amc.png?nolink&400 |}}
+//**figure 4.2**// Graph depicting Deep-Sleep schematics set up for ESP32/
+======  Code & Description======
+<code c++>
+*//There are 2 ways to wake up a system, those are called Interrupts.
+*//hardware Interrupts are based on external events where signals are sent to the GPIO.
+*//Software Interrupts occur when we program the device, like through a wake up alarm or timer.
+#define uS_TO_S_FACTOR 1000000           *//Equation to convert milliseconds to Minutes
+#define TIME_TO_SLEEP  10                *//Determined amount of minutes at sleep
+RTC_DATA_ATTR int bootCount = 0;
+*//Data has to be stored in the Real time Clock (RTC) fast memory because the CPU memory is wiped on every boot.
+*// The amount of data has to be minimal due to size limitations : 8bit fast memory and 8bit Slow memory.
+*//Power outages and resetting the board will erase the RTC memory, therefore its use should be limited to non essential information.
+*//Therefore we decided to just Keeping data of times awaken in internal RTC, this will help us see if any issues occur.
+**************Wake Up Print **************************************************************
+void print_wakeup_reason(){                       *//Set up to list reasons for system wake-up
+  esp_sleep_wakeup_cause_t wakeup_reason;
+  wakeup_reason = esp_sleep_get_wakeup_cause();   *//System wakes up due to 3 reasons
+  switch(wakeup_reason)
+  {
+    case ESP_SLEEP_WAKEUP_EXT0 : Serial.println("PUSHED BUTTON caused the system to WAKEUP"); break;
+    case ESP_SLEEP_WAKEUP_TIMER : Serial.println("TIMER caused the system to WAKEUP"); break;
+    default : Serial.printf("DeepSleep didn't wake up ESP32: %d\n",wakeup_reason); break;   *//Initial Boot will yield this reason
+  }
+}
+*//We made the system wake up due to the internal timer and a pushed button,
+*// the reason for the push button is that in the case we can take a measurement at our will without having to wait for the timers.
+*//An external clock could be added to the device, however Grafana already designates time and date of transferred data.
+void setup(){
+  Serial.begin(115200);
+  delay(1000);
+  pinMode(32,OUTPUT);         *//Illuminates a LED when the system is awake. For visual confirmation.
+  pinMode(33,INPUT_PULLUP);
+   *//ESP32 has pull-up resistors built on the pins, when we activate it
+   *//it avoids the use of external resistors
+   *//INPUT_PULLUP keeps the signal HIGH by default
+   *//floating currents which can produce erroneous readings are avoided by pull up/down resistors
+  for(int i=0;i<5;i++)
+{
+  digitalWrite(32,HIGH);       *// These are the parameters for the LED flashing
+  delay(1000);
+  digitalWrite(32,LOW);
+  delay(1000);
+  }
+  ++bootCount;
+  Serial.println("Reboot count number: " + String(bootCount));     *//We want to know how many times the system has booted
+                                                                   *//easy way to know if there are issues internal or battery
+                                                                   *//issues
+  print_wakeup_reason();
+  esp_sleep_enable_ext0_wakeup(GPIO_NUM_33,0);
+*//During Sleep only Pins connected to the RTC are operational
+*//A General Purpose Input/output pin are used to perform digital readings and output functions.
+*//By default those pins have no predefined purpose.
+*//The pin used has to be named after their GPIO
+  esp_sleep_enable_timer_wakeup(TIME_TO_SLEEP * uS_TO_S_FACTOR);                   *//conversion factor to minutes
+  Serial.println("ESP32 is going into DeepSleep for " + String(TIME_TO_SLEEP) +    *//Script detailing the process
+  " Seconds");
+  Serial.println("Going to sleep now......");
+  delay(1000);
+  Serial.flush();                                                                  *//To avoid mistakes in data transmission by
+                                                                                   *//clearing buffer
+  esp_deep_sleep_start();
+}
+</code>
+*** There is no loop section in our coding because the micro controller will go into deep sleep before reaching that part//
+of the code, which means everything has to be written in the void set up section of the sketch.//
 ======  Results ======
+{{ :amc2022:grouph:serial_monitor_deepslep.png?nolink&500 |}}